Saller : GTT TECH M SDN BHD
Email : gtttech@yahoo.com
: gtttech09@gmail.com
BIO-RUST REMOVER
- Non-Toxic
- No Fumes
- Biodegradable
- Environmentally Safe
- Eliminates rust efforlessly in minutes.
FACT SHEET
Is a revolutionary new product that removes rust in the safe, easy to use, and envirenmentally
friendly manner.The product has been proven effective to remove even deep rust on all type
friendly manner.The product has been proven effective to remove even deep rust on all type
of mind steel and iron.Global Rust Remover will de-rust without dis-mantling.It will not harm
copper, brass, aluminium, plastic, rubber, vinyl, solder points or lead. Evan more amazing,
Global Rust Remover will not remove non-oxide coatings,such as paints or chrome that are
still bonded to the surface.It only attacks rust and leaves other materials intact.
Some of the key benefits of using.
- Developed as an industrial strenght rust remover
- Removers rust in as little as 10 minutes.
- Non-toxic, non-corrosive
- No fumes or bad odors
- Non-flammable, no Volatile Organic Compounds (VOC's)
- Easy to use, just soak part in room temperature solution
- Requires no special equitment, safe of skin.
- Biodegradable, water soluble.
- No acids, bases,solvents or other toxic ingredients.
- Will nor harm un-rusted stell, safe on other metals.
- Will not effect plastic, PVC, Viton and most paints.
- Re-usable solution-one gallon de-rusts up to 300 pounds of heavily rusted steel.
- Can be disposed of safety into sewer systems.
- Also works as an excellent short term rust inhibitor.
HOW TO USE
Bio-Rust remover ( Evapo-Rust ) is easy to use. Fully immerse the rusted item in Bio-Rust Remover and check progress in about 30 minutes; no scrubbing necessary. Soak times will vary from 30 minutes to 24 hours depending on severity of rust, type of steel, and bath temperature. Bio-Rust Remover is water based, therefore the process will slow down as temperature decreases and increase as temperature increases. We recommend utilizing Bio-Rust Remover at a bath temperature above 60° F.
Once rust is removed, rinse item with water. You can now paint, plate, or apply a long term Corrosion Preventative Compound (CPC). For short term rust inhibition, simply dip the item in Bio-Rust and allow to dry. Rinse with water before painting, plating or applying a CPC.
HOW TO USE
PREPARATION (suggestions for best results):
CLEAN & RINSE THE ITEM PRIOR TO DE-RUSTING:
(Item should be free of mud, dirt, loose rust, oil, and grease.)
WHY?
1.) BIO-RUST REMOVER DOES CONTAIN A SURFACTANT TO HELP IT OVERCOME DIRT, OIL, AND SOME GREASES. HOWEVER, EVAPO-RUST IS A RUST REMOVER, NOT A CLEANER AND THE PERFORMANCE MAY BE AFFECTED, ESPECIALLY FROM GREASES.
2.) BIO-RUST REMOVER IS SEWERABLE AS SUPPLIED. ADDING OILS AND GREASES MAY CHANGE THE STATUS OF THE DISPOSAL. IF YOU ARE ONLY DE-RUSTING CLEAN STEEL, ALL THAT REMAINS IS CHELATED IRON AND WATER. IN MOST CASES, ONLY THE IRON CONTENT SHOULD DICTATE THE DISPOSAL REQUIREMENTS. (check local restrictions and dispose of according to local, state, and federal guidelines.
3) RINSING ASSURES YOU WILL NOT BE DRAGGING OTHER CLEANERS INTO THE BIO-RUST REMOVER SOLUTION. RAISING THE pH OF EVAPO-RUST WITH OTHER CHEMICALS CAN RENDER THE SOLUTION USELESS.
BEFORE
BEFORE
AFTER
How Does Bio-Rust Remover ( Evapo-Rust ) Works?
Bio-Rust Remover ( Evapo-Rust ) works at pH of 6.1 to 7( neutral ) through selective chelation. This is a process in which a large synthetic molecule forms a bond with
metals and holds them in solution. Most chelating agents bind many different metals.
The active ingredient in Bio-Rust Remover ( Evapo-Rust ) bonds to iron exclusively.
It can remove iron from iron oxide, but is too weak to remove iron from steel because
the iron is held much more strongly.
Sample Before and After
Tiada ulasan:
Catat Ulasan